Well Watcher™ Installation Resources
The Well Watcher™ System uses adjustable water collection to gradually collect and store water from the well, then delivers the stored water to the home at consistent pressure using a booster pump.
Unlike the Well Manager®, the Well Watcher™ works in conjunction with the home’s existing pressure tank and pressure switch. Proper system placement, plumbing, filtration, electrical connections, and setup are important to ensure the system operates as intended.
Your Installation Guide
Every Well Watcher™ System includes a detailed installation guide with system-specific instructions for plumbing, electrical connections, setup, startup, testing, and maintenance. Your installation guide is provided with your system and should be reviewed by you and your installer before installation begins.
The resources below are designed to help you plan ahead and better understand the installation requirements for your Well Watcher™ System.
Jump to a Section
Where the Well Watcher™ Fits in Your Water Line
The Well Watcher™ is installed after the home’s existing well pressure tank and pressure switch, allowing the existing well equipment to continue controlling the well pump while the Well Watcher™ collects and stores water for later use.
A 50-micron sediment filter is required on the incoming line before water enters the Well Watcher™ System. Additional water treatment equipment can be incorporated based on the home’s existing water treatment setup.
Diagram highlights pre- and post-filtration recommendations for a complete setup.
Installation Note: For best performance and to help prevent rapid pump cycling, install a bladder tank on the discharge side of the pump. DAB recommends sizing the bladder tank based on your pump’s normal peak flow:
- 2-gallon bladder tank – E.SYBOX Mini 3 (approximately 10 GPM)
- 4-gallon bladder tank – E.SYBOX, DTRON 2, and DIVER (approximately 20 GPM)
- 10-gallon bladder tank – E.SYBOX MAX (approximately 50 GPM)
Have Existing Water Treatment?
Water softeners, iron filters, UV systems, and other treatment equipment can be incorporated into a Well Watcher™ installation. Placement may vary depending on the type of treatment and your existing water system.
If you’re unsure where your existing equipment should be located, contact our team for help reviewing your installation layout.
System Dimensions & Space Requirements
Well Watcher™ Systems are available in multiple tank orientations and pump configurations to accommodate different installation spaces. Review the dimensions of your system before installation, including the space needed for the tank, booster pump, plumbing connections, and access for future service.
Vertical 210 gallon
L41″ x W24″ x H64″
Effective Water Storage: 195gal
Horizontal 210 gallon
L64″ x W24″ x H42″
Effective Water Storage: 185gal
Low Horizontal 210 gallon
L64″ x W37″ x H28″
Effective Water Storage: 175gal
Vertical 100 gallon
L27″ x W24″ x H52″
Effective Water Storage: 90gal
Your Pump Configuration Can Affect System Space
The amount of installation space required can vary depending on the booster pump selected and whether the pump is installed internally, externally, wall-mounted, or alongside the system.
Review your specific system configuration when planning the installation area, and allow adequate space for plumbing connections and future access to the pump and system components.
Planning a Multi-Tank System?
Additional storage tanks can be added to increase available water storage. Because multi-tank systems can be arranged differently depending on tank orientation, pump configuration, and available space, overall dimensions will vary by installation.
Contact our team if you need help determining the footprint or layout of your specific configuration.
Plan for the Weight of a Filled System
A filled Well Watcher™ 210 tank can exceed 1,800 lbs. The system must be installed on a level concrete slab or a properly reinforced wood or steel subfloor capable of supporting the filled system.
Condensation should also be considered when selecting the installation location. A condensation pan and access to a nearby floor drain or sump area are strongly recommended.
Built for Water Storage
Well Watcher™ Systems use durable polyethylene tanks designed for potable water storage. Their ribbed construction provides added strength, with multiple tank orientations available to accommodate different installation spaces.
Explore our water storage tanks for more information about tank construction, dimensions, orientations, and features.
Simple Plumbing Connections
Well Watcher™ Systems arrive pre-assembled with much of the system plumbing already in place. For a typical installation, your installer will connect the incoming well line to the system and connect the system outlet back into the home’s main water line.
Standard Well Watcher™ Connections
- Inlet: 1/2″
- Outlet: 1″
A 3/4″ and 1″ inlet are available by custom order. Installers can also use appropriate reducers or adapters as needed to connect the system to existing household plumbing.
The piping between the storage tank and booster pump is typically provided by Well Manager based on the selected system and pump configuration. If the booster pump will be mounted away from the system, additional on-site plumbing may be required.
Plumb In → Well Watcher™ System → Plumb Out
Filtration & Expansion Tank
Plan for the required pre-filtration and expansion tank when completing your Well Watcher™ plumbing connections. Refer to the system layout and pump information above for placement and sizing details.
Plan for Overfill Drainage
The Well Watcher™ includes an overfill safety connection near the top of the tank as a backup in the event of an unexpected overfill. This connection must be routed to an appropriate drainage location, such as a floor drain, sump basin, standpipe, or other approved drainage area.
Plan for drainage when selecting your system location. Flexible tubing or PVC can be used to safely direct overflow away from the system and surrounding floor area.
Need a Different Plumbing Configuration?
The Well Watcher™ is built with a standard 1″ inlet and 1″ outlet. A 3/4″ or 1″ inlet can be requested as a custom option, and installers may use reducers or adapters where needed to connect the system to existing plumbing.
If your project requires a different pump location, piping arrangement, or a custom commercial configuration, let our team know before your system is built.
Electrical Requirements
The Well Watcher™ System and booster pump require proper electrical service for safe and reliable operation. Electrical requirements vary depending on the booster pump selected, so available power should be considered when planning your system configuration and installation location.
Well Watcher™ System
115V
Dedicated 15A Circuit
Booster Pump
Varies by Pump
Requirements depend on the selected booster pump.
Electrical Installation
Dedicated circuits are required and should not be shared with other equipment. Connections to the home’s breaker system should be completed by a licensed electrician and must follow applicable local electrical codes.
Always disconnect power before working on system wiring or electrical components.
Booster Pump Options
The Well Watcher™ can be configured with different booster pumps based on your home’s water demand, desired pressure, available electrical service, and installation space.
Your selected pump may be installed inside the tank, alongside the system, or in another suitable location depending on the pump and system configuration.
For pump specifications, electrical requirements, dimensions, and available options, visit our Booster Pump Options page.
Optional Cycle Sensor
A Cycle Sensor can be added to a Well Watcher™ System to provide additional protection for the well pump. It monitors well pump operation and can help protect the pump if the well is unable to supply water as expected.
If your Well Watcher™ includes a Cycle Sensor, setup instructions are provided with your system. Our team can also help determine whether a Cycle Sensor is recommended for your well and system configuration.
Well Watcher™ Installation FAQs
Does the Well Watcher™ use my existing pressure tank?
Yes. Unlike the Well Manager®, the Well Watcher™ works in conjunction with your existing pressure tank and pressure switch. Your existing well equipment continues to control the well pump, while the Well Watcher™ collects and stores water for later use.
How is the Well Watcher™ collection rate adjusted?
The Well Watcher™ uses an adjustable fill rate that can be set based on the amount of water your well can reliably supply. This allows the system to collect and store water gradually rather than relying on the well to meet the home’s water demand all at once.
Detailed setup instructions are provided in the installation guide included with your system.
Can I use my existing water treatment equipment?
Yes. Water softeners, iron treatment, UV systems, and other water treatment equipment can be incorporated into a Well Watcher™ installation. Placement depends on the type of equipment and your existing water system.
If you’re unsure how your treatment equipment should fit into the installation, contact our team for layout assistance.
Can my plumber install a Well Watcher™?
Yes. The Well Watcher™ can be installed by a qualified plumber, well professional, or other experienced installer. Electrical connections to the home’s breaker system should be completed by a licensed electrician and all plumbing and electrical work must follow applicable local codes.
We recommend that both the system owner and installer review the Well Watcher™ Installation Guide before installation begins.
5. Do I need a Cycle Sensor with my Well Watcher™?
A Cycle Sensor is an optional addition to the Well Watcher™ System that provides additional well pump protection. Whether one is recommended depends on your well and system configuration.
Our team can help determine whether a Cycle Sensor would be beneficial for your installation.
Can Well Manager help my installer before or during installation?
Yes. Our team can help answer questions about your system configuration, placement, pump setup, plumbing, electrical requirements, and other installation considerations. We can also provide custom system layouts when additional planning is needed.
For more involved installation questions, you or your installer can schedule a call with our team to review the system and discuss your installation needs.
Preparing for Your Well Watcher™ Installation?
Your Well Watcher™ System will arrive with a detailed installation guide specific to your system and configuration. Be sure to review the guide with your installer before beginning installation.
If you or your installer have questions while planning or installing your system, our team is available to help with system placement, plumbing, electrical requirements, setup, and other installation questions. You can also schedule a call with our team for additional installation support.
Need Help Visualizing Your Installation?
Every installation is different. Our team can create a custom system layout to help you better understand how your Well Manager system may fit, connect, and be configured before installation.
Layouts can be tailored to your space, system configuration, pump selection, water treatment equipment, and other installation needs.
- Photos of the proposed installation area
- Overall room or available-space dimensions
- Ceiling height and doorway/access measurements
- Existing plumbing and incoming water-line location
- Pressure tank and water treatment locations
- Available electrical service
- Furnaces, water heaters, appliances, or other equipment that cannot be moved
Space & Placement
System Dimensions
Plumbing & Equipment
